First check whether the type and name of the anti-corrosion paint meet the requirements for use. After the anti-corrosion paint is opened, it should be thoroughly stirred to make the precipitate evenly mixed. Two-component paint must be blended on site according to the ratio, engineering dosage and permitted construction time specified in the specification.
ET-98 inorganic phosphate long-acting zinc-rich coating. The mixing ratio of A and B is 1:2. The zinc powder of component A is poured into component B, mixed and mixed, and matured for 20 minutes.
Chlorinated rubber topcoat. The chlorinated rubber topcoat is a single-pack coating, which can be used evenly after being opened.
Formulation of H06-1 epoxy zinc-rich antirust primer. The ratio of combination of A and B is component A: component B = 4:1. Add component B to the vat of component A, stir well, and let it stand for 20 minutes before use.
The preparation of 70-H epoxy iron red anticorrosive paint and ZHL51-2 super thick pulp epoxy asphalt anticorrosive paint can be carried out in the same way.
H06-3 epoxy cloud iron antirust paint. The mixing ratio of A and B is component A: component B = 4:1. Add the B component of the small bucket to the vat of the component A, stir well, and let it stand for 20 minutes before use.
Airless high pressure spraying methods can be used, or manual or air spray construction methods can be used. In order to ensure the thickness of the paint film in the welding, corners, corners, etc., before the large-area painting, the paint should be pre-sprayed. When painting, the operator should always measure the wet film thickness with a wet film thickness gauge. When painting, the upper and lower rear and left and right, or the vertical and horizontal painting methods of the upper and lower sides and the upper and lower sides should be adopted to make the anti-corrosive paint film smooth and even and uniform in thickness. The surface treatment quality is checked according to the color photographs in the national standard. Check the surface condition of the paint film with the naked eye. The paint film should be free from pinholes, shedding, sag, cracks, and leakage coating.
The dry film thickness is measured by a paint film thickness gauge. The thickness of the paint film should be determined after each application. The total thickness of the paint film must be determined after the coating is completed. One point is measured every 1-3 square meters, and the thickness value of more than 90% of the measuring points must reach the specified value, and the film thickness that does not reach the specified value is not less than 90% of the specified value. Whether it should be recoated or overcoated.
Concerned about surprises
Label: painting component thickness value epoxy asphalt construction method
Previous: Common knowledge of fasteners: difference between cold-twist nut and hot-twist nut Next: High-gloss non-melting mold technology will replace spraying process
Industrial sectional doors are the most durable and longest lasting doors to ensure circulation at the areas of the factory entrance and exit of goods, loading and unloading areas.
The body of sectional door is forming by 40 mm sandwich panels. These panels provides sound and heat insulation due to the intense doped polyurethane insulation was injected between galvanized steel sheet. (50 kg/m3).
Industrial sectional door systems provide space-saving with opening parallel to the ceiling.Any opening can be used clearly . and produces in accordance with the transition range and the height in the factory buildings or warehouses.
Doors is working sliding by be the most appropriate the gap between the top level of the gate with a ceiling height within the side rasils. The door can be mounted in different ways according to the gap distance (standard, low, highlift and vertical track systems).
Industrial sectional doors can easily be opened automaticly by 230-380 V-AC/50 Hz electric motor or manualy thanks to torsion spring system that balances the weight of the door.The galvanized springs are made to be durable of 25.000 door cycles.Motor with emergency chain All the drive systems have a mechanical back-up system fitted to the reduction gearbox of the electric motor, so that the sectional door can be opened if the power fails. The reduction gearbox can then be powered using the chain.
Industrial Sectional Door,Industrial Overhead Sectional Door,Industrial Warehouse Sectional Door,Industrial Garage Interior Sectional Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hffreezerdoor.com