Maybe a lot of people after buying the toilet, just find someone who is decorating the team to install it, even if you can't do it, you can't do it. Today, Go Jiaju.com Xiaobian probably briefly introduces the process of installing a professional toilet .
The toilet installation method is as follows:
1. Before the installation, the master will first conduct a comprehensive inspection of the sewage pipeline to see if there are any mud and sand, waste paper and other debris in the pipeline. At the same time, check whether the floor of the toilet installation is horizontal or not. If the ground is found to be uneven, when installing the toilet The ground should be leveled. Saw the spout, and allow the drain to be 2mm-5mm above the ground as much as possible.
2. Before selecting the toilet, first determine the size of the water in your house. What is the distance between the water outlet and the wall? (The standard is only 300, 400 mm).
3, then choose the style you like according to the size, pay attention to choose the water-saving type (3-6 liters), order to see the model, the origin, the current product is mixed, the shop is no regrets choice.
4, before the toilet installation to determine whether you choose the product, accessories, instructions are complete, take a closer look at the manual, understand some product matters, in order to prevent the beam from changing columns, cutting corners, remember.
5. The water outlet requires the installer to handle the leveling. The bottom outlet of the toilet should be equipped with a special flange for the toilet seat, or evenly coated with the glass glue and the water outlet. The bottom of the toilet bowl and the surrounding area are glued. The toilet and the wall are evenly spaced and placed. Correct and steady.
6. After the toilet seat is in place, the water is required to have no leakage, the water level is correct, the flushing is smooth, the switch is flexible, and the cover is stable.
7. At present, the toilet seat is generally not equipped with anchor screws, but the reserved holes on the toilet should be blocked with glass glue to prevent the smell.
8. If the anchor screw is installed, first use the special sealant installed in the toilet to spread evenly on the outer 2CM of the base of the toilet base. The drain of the toilet should face the center of the drain pipe and draw a seat. The position of the expansion bolt on the left and right sides of the toilet, remove the toilet, punch, and bulge the plug. It should be noted that this newly-punched expansion bolt is embedded in the hole and may break the waterproof layer. It is recommended to pre-embed the expansion screw. At the same time, fill the seal around the hole, then bury the bolt, first screw the expansion bolt, let the expansion bolt completely release, strengthen its tension, then screw off the upper screw, put the toilet, Then screw the screws directly to the cap to maintain the overall appearance. At the intersection of the toilet bowl and the outer surface of the ground surface, because the toilet bowl and the ground surface are not integrated, the joint seal transparent sealant can be used for stirring, and the outer mouth of the toilet bowl is sealed to maintain the integrity with the ground surface. Partial bathroom water can be blocked on the outside of the toilet.
9. After the toilet is installed, wait until the glass glue (soot) or cement mortar is solidified before releasing the water. The curing time is generally 24 hours. If you are not a professional person to install, usually in order to save trouble, the construction workers will directly use cement as a binder. This is definitely not enough. Fill the fixed position of the toilet seat. In fact, there is a drawback in the middle. The cement itself has swelling and it takes a long time. This method may lead to cracking of the base of the toilet and it is not convenient for maintenance.
10. Install or commission the water tank fittings. First check the water pipe, drain the pipe for 3-5 minutes to ensure the clean water pipe; then install the angle valve and connecting hose, then connect the hose to the installed water tank fitting inlet valve and press the water source to check the water inlet. Check whether the valve water inlet and sealing are normal, check whether the installation position of the drain valve is flexible, whether there is any jam or leakage, and check whether there is any leaking inlet valve filter device.
The above is the toilet installation method introduced by Xiaobian for everyone. I hope that I can help you and more relevant information. Please look forward to the follow-up report of Xiaojiaju.com.
Wireless pressure transmitter is high accuracy and low consumption wireless pressure measuring device. NB-lot LORA GPRS wireless spread spectrum communication technology is used for remote data transmission. It is simple to install, without onsite wiring,which save construction cost, especially suitable for not easy wiring and unable to power supply.
Wireless Pressure Transmitter,Wireless Pressure Sensor,Wireless Pressure Transducer,Wireless Differential Pressure Transmitter
Xi'an Gavin Electronic Technology Co., Ltd , https://www.cngamicos.com