(1) Varnish construction process:
Clean the surface of the woodware → Polished paper → Polished powder → Polished sandpaper → Full scrape the first time putty, sandpaper polishing → Full scraping the second time putty, fine sandpaper polishing → Brushing oil color → Brush the first time varnish →Fight for color, refill putty, fine sandpaper polish → brush the second time varnish, fine sandpaper → brush the third time varnish, polishing → sandpaper polishing fade, wax, polish.
(2) Mixed color paint construction process:
First, clean the dust on the surface of the base layer, repair the base layer → level off with matte paper → paint on the frugal part → puttying on the bottom → dry oil → first pass paint scraper → polishing → brushing primer → primer Dry hard → brushing the surface layer → repair putty to repair → polish wipe the third time the paint brush brush the second time coating → polishing → third paint finish → polishing wax.
2. Construction points
Clean oil coating construction specification
Polishing the base layer is an important process for painting the varnish. Firstly, dust, dust, and other impurities on the wood surface should be removed.
On the oil is also an important process varnish brushing, construction with cotton silk oil coated on the surface of the wood, rubbed back and forth by hand, rubbed oil into the eyes of the wood.
When brushing the oil, the brush should be easy and natural, and the finger should be lightly applied, so as not to move loose and not touch the brush.
When brushing, you must follow the order of multiple times, less time and less time, and the time required for the operation. Follow the order of brushing first, backwards, first, then first, then left, then right, first inside and then outside, and then brush. Vertical operation method construction.
Construction specification for wood surface oil mixing
When processing at the grass-roots level, in addition to cleaning up debris from the grass-roots, local putty embedding should also be performed. Sanding paper should be ground along the wood grain.
Before painting the surface layer, apply a paint sheet (shellac paint) on the bottom of the joint where there is a large amount of color difference and lignanization. Should be painted on the grass-roots dry oil or mooring, brushing dry oil layer to brush all parts of the uniform, can not miss the brush.
After the base oil dries out, it is full of scrape the first time putty, dry after the sanding with hand-made sandpaper, and then make up high-strength putty, putty to pick the wire does not fall prevail. When painting surface paint, it should be polished with fine sandpaper.
Three trees paint paint paint
Previous Good paint, paint your wonderful world!
Next The paint drips, sags, and the paint film is uneven
Wood paint construction process
1. Main construction techniques (1) Lacquer construction process: Cleaning the surface of the wood surface → Polishing the sandpaper → Polishing powder on the sandpaper → Polishing the sandpaper → Filling and scraping the first time Putty, sandpaper polishing → Filling and scraping the second time Putty, sand paper grinding Light → paint oil → brush the first time varnish → fight to find the color, make up for putty, fine sandpaper polishing → brush the second time varnish, fine sandpaper → brush the third time varnish, polishing → sandpaper sanding back Light, wax, polish. (2) Color mixing paint...
1, before use should be strictly in accordance with the ratio in the instructions for use, polyester paint according to the construction requirements to add supporting thinner diluted to the construction viscosity. 2. When multi-component polyester lacquer is formulated, it should be thoroughly mixed and allowed to stand for about 15 minutes in order to facilitate the pre-aging reaction between the components and eliminate bubbles generated during stirring. 3. When spraying or brushing, ensure that the substrate is dry. The moisture of substrate is easy to cause film peeling, blistering, shedding and so on. At the same time, the film thickness should be strictly controlled....
First, wood paint construction environment Wood paint construction requires a suitable environment and conditions, such as temperature, humidity, light, ventilation, health, etc. can make a good effect. Wood paint construction is best carried out at room temperature (15-30 °C) conditions, the temperature is too low, paint film becomes slower; temperature is too high (more than 35 °C), brushing performance will be adversely affected. Avoiding damp air is not good for most paints, especially lacquer, polyurethane paint, etc. In wet and rainy weather...
Wood lacquers are highly flammable liquids that may cause discomfort when inhaled or in contact with the skin, so the product is intended for use only by professionals.
submit
Stainless Steel Welded Square Tube
Stainless Steel Welded Square Tube,Round Stainless Steel Welded Tube,Welded Square Tube,Stainless Steel Welded Steel Tube
Foshan Maysky Stainless Steel Co., Limited , https://www.mayskysteel.com