When using geothermal floors, consumers must pay attention to the gradual heating of floors and floors. When installing, the surface temperature should be maintained at about 18°C. Before installation, gradually increase the temperature of the concrete floor by 5°C per day until it reaches the standard of about 18°C.
North American maple
How to properly use floor heating, and to maximize the protection of the floor, so that when we usually use floor heating, it should be worth paying attention to, this site Xiaobian especially for everyone to make the following points:
1. The heating should be gradual when used for the first time;
When using geothermal floors, consumers must pay attention to the gradual heating of floors and floors. When installing, the surface temperature should be maintained at about 18°C. Before installation, gradually increase the temperature of the concrete floor by 5°C per day until it reaches the standard of about 18°C. In the first 3 days after the installation is completed, the temperature should be maintained. After 3 days, the temperature can be increased as needed, and the temperature can only be increased by 5°C per day.
The first use of geothermal heating, attention should be slowly warming. When used for the first time, gradually increase the temperature in the first three days of heating: the first day of water temperature is 18°C, the next day is 25°C, the third day is 30°C, and the fourth day can be raised to normal temperature, ie, water temperature 45°C, surface temperature 28 °C ~ 30 °C. Can not warm up too quickly, too fast, the floor may be cracked due to expansion.
When the geothermal heating system is turned on again after a long period of time, it must be heated in strict accordance with the heating procedure as it was for the first time.
2, the surface temperature can not be too high;
It should be noted that with geothermal heating, the surface temperature should not exceed 28°C, and the temperature of the water pipes should not exceed 45°C. If this temperature is exceeded, the service life and life cycle of the floor will be affected. In general families, when the room temperature in winter reaches about 22°C, it is already very comfortable. If the temperature rises normally, it will not affect the use of geothermal floors.
3, shut down the geothermal system, pay attention to gradual cooling;
With the passage of the seasons, when the weather is warm and indoors no longer requires geothermal heating, attention should be paid to shutting down the geothermal system. There must also be a process of cooling down the floor. The cooling process of the floor must also be gradual, not abruptly reduced, if the cooling rate is too fast, It will also affect the life of the floor.
4, when the room is too dry, humidification can be considered;
In winter, the climate is dry, and geothermal heating is used. If the floor is exposed to high temperatures for a long time, it will be easy to crack. At this time, the owner must humidify the room so as not to crack the floor.
During the renovation, attention should be paid to not punching holes or nails on the ground so as not to leak geothermal pipes, causing the geothermal system to run out of water and the floor foam to be scrapped. In addition, because the surface of the floor is a heat-dissipation surface, the floor should not be fixed or decorated with legless furniture. It is also not suitable to build a platform to avoid affecting the flow of hot air, resulting in poor heating of the room.
Due to the relatively high surface temperature of the floor, it is best not to place glassware and chinaware directly on the ground in winter when using a geothermal heating system, so as to avoid uneven heating, heat expansion and contraction, and rupture of the vessel. .
Geothermal floor has become a fashion decoration in home decoration, but everyone must pay more attention to detail when purchasing and paving, especially in terms of maintenance, the requirements for geothermal floor are higher.
Home Care Flooring Purchase Nature Flooring Room Decoration Cement Heating Interior Decorating Glass Furniture Home Decorations Home Furnishing
The working principle of a High Flow Peristaltic Pump like a snake swallowing an egg. The hose is constantly squeezed through the roller to make the hose generate pressure and push the liquid forward. Our designers make the Peristaltic pump head and hose fit perfectly by designing precise roller size and pump head structure. So as to achieve the purpose of accurate liquid metering transmission or filling
1. Clean and pollution-free: the fluid only passes through and touches the peristaltic pump hose.
2. High precision: constant current, reproducibility of up to 0.5%, and flow can be precisely adjusted.
3. Low shear force: It is an ideal tool for conveying shear-sensitive and corrosive fluids.
4. Corrosion resistance: it can transport various fluids, such as organic solvents and corrosive liquids.
5. Idling and dry operation: air or gas-liquid-solid three-phase mixed transportation can also be transported.
6. Possess self-priming ability: self-priming, no need to fill the pump, no need to empty.
7. With stop valve function, no siphon, no seals, stop valve and check valve function.
8. Two-way conveying function: reverse pumping and back-suction functions can be realized by changing the direction of the pump runner.
9. Simple maintenance: only need to replace the peristaltic pump hose, no valve and seal replacement.
High Flow Peristaltic Pump,Additive Peristaltic Pump,Polishing Liquid Pumps,Intelligent Transfer Peristaltic Pump
Baoding Chuangrui Precision Pump Co., Ltd. , https://www.chuangruipump.com